Tugela Bush Shirt - Taupe

Norsafe Management Shirts

Norsafe Management Shirts

On Site Management

Katima Vented Shirt

Vented back to promote air circulation
Chest pockets with velcro flap closure and pen devision
Generous side entry utility pockets
Mock horn buttons
Rounded shirt hem
Double-needle topstitched throughout
MATERIAL
100% cotton
2/1 fine twill 140 g/m² OEKO-TEX®
STANDARD 100 Certified
FIT
Regular fit

Expedition Bush Shirt

Fully fused sun protector collar
Back locker loop and box pleat
Chest pockets with Velcro closures and box pleats
Pockets attached with double needle
Mock horn buttons
Rounded shirt tail
Double needle topstitched throughout
Soft-washed and pre-shrunk
MATERIAL
100% cotton 2/1 fine twill 140 g/m²
FIT
Relaxed fit

Delta Two Tone Bush Shirt

Stay comfortable and stylish in the Delta Two Tone Bush Shirt.
Made from Classic soft fused collar
Contrast front and back yokes
Chest pockets with velcro flap closures and box pleats
Pen division on left chest pocket
Double needle topstitched throughout
Mock cuffs
Mock horn buttons
Rounded shirt tail
MATERIAL
100% cotton 2/1 fine twill 140 g/m²
OEKO-TEX® STANDARD 100 Certified
FIT
Relaxed fit

Tugela Bush Shirt

Classic soft fused collar
Chest pockets with velcro flap closures and box pleats
Pen division on left chest pocket Double-needle topstitched throughout
Mock cuffs
Mock horn buttons
Rounded shirt tail
MATERIAL
100% cotton
2/1 fine twill 140 g/m² OEKO-TEX®
STANDARD 100 Certified
FIT
Relaxed fit

Safety Boots Durability Test

We put our safety boots through the wringer so you don’t have to

#SafetyFirst #BootTest #Durability #NorsafeQuality #ToeProtection

How to DIY Test the Durability of Safety Boots (At Home)

You don’t need a laboratory to get a realistic idea of how durable safety boots are. While certified testing must follow formal standards, there are several simple DIY checks you can do at home or in a workshop to spot weak boots early.

These tests won’t replace official certification — but they will expose poor quality fast.

Important Note Before You Start

DIY tests are for evaluation only, not certification.
For legal compliance, boots must still meet standards like SABS / SANS 20345.

That said — bad boots don’t magically become good in a lab.

1. DIY Sole Wear Test (Abrasion)

What you need:

Rough concrete or paving

Your body weight

5–10 minutes

How to test:

Place one boot flat on concrete

Grind the sole back and forth using pressure

Focus on the heel and ball of the foot

What to look for:

❌ Soft rubber shedding quickly

❌ Smooth patches forming fast

✅ Minimal visible wear

Why it matters:
If the sole wears fast here, it’ll disappear on site.

norsafe-DIY Sole Wear Test

3. DIY Water Resistance Test

What you need:

  • Basin or bucket

  • Water

  • Dry socks or paper towel

How to test:

  1. Place dry paper towel inside the boot

  2. Stand the boot in water (about ankle deep)

  3. Bend the sole repeatedly for 5 minutes

Results:

  • ❌ Wet paper = failure

  • ❌ Leather soaking up water = short lifespan

  • ✅ Inside stays dry

2. DIY Flex & Crack Test

What you need:

  • Your hands

  • A table edge

How to test:

  1. Bend the boot sharply at the ball of the foot

  2. Repeat 50–100 times

  3. Watch closely where the sole meets the upper

Red flags:

  • Cracks forming

  • Glue separating

  • Upper pulling away from sole

Reality check:
This is where most boots fail first.

norsafe-DIY Flex & Crack Test